Microchip PIC32MX 32位MCU多媒體擴展板解決方案

Microchip公司的多媒體擴展板(MEB)采用PIC32系列32位MCU,為PIC32入門板用戶,dsPIC33E或PIC24E USB入門板用戶提供了靈活解決方案,以開發更高級用戶接口.MEB集成了3.2 Color TFT觸摸屏QVGA顯示器,FCC認證WiFi模塊,24位立體聲音頻代碼,三軸加速度計,操縱桿和MicroSD存儲器卡插槽,簡便和DM320001, DM320003-2, DM320004, DM330012 以及DM240012入門板連接,可用于圖像/用戶接口,以太網/USB/CAN連接,多任務嵌入式控制以及高性能音頻.本文介紹了PIC32MX主要特性,方框圖,多媒體擴展板(MEB)主要特性,方框圖,電路圖,材料清單和PCB元件布局圖.

PIC32MX1XX/2XX:32-bit Microcontrollers (up to 128 KB Flash and 32 KB SRAM) with Audio and Graphics Interfaces, USB, and Advanced Analog

Microchip’s 32-bit portfolio with the MIPS® M4K® offers high performance microcontrollers, and all the tools needed to develop your embedded project. With free software, low cost development tools, and pin/peripheral compatibility from 16-bit product lines, PIC32 MCUs shorten time to market and allow your designs to grow. PIC32 gives your application the processing power, memory and peripherals your design needs!

PIC32MX主要特性:

Operating Conditions

• 2.3V to 3.6V, -40ºC to +105ºC, DC to 40 MHz

Core: 40 MHz MIPS32® M4K®

• MIPS16e® mode for up to 40% smaller code size

• 1.56 DMIPS/MHz (Dhrystone 2.1) performance

• Code-efficient (C and Assembly) architecture

• Single-cycle (MAC) 32x16 and two-cycle 32x32 multiply

Clock Management

• 0.9% internal oscillator

• Programmable PLLs and oscillator clock sources

• Fail-Safe Clock Monitor (FSCM)

• Independent Watchdog Timer

• Fast wake-up and start-up

Power Management

• Low-power management modes (Sleep, Idle)

• Integrated Power-on Reset and Brown-out Reset

• 0.5 mA/MHz dynamic current (typical)

• 20 μA IPD current (typical)

Audio Interface Features

• Data communication: I2S, LJ, RJ, DSP modes

• Control interface: SPI and I2C™

• Master clock:

- Generation of fractional clock frequencies

- Can be synchronized with USB clock

- Can be tuned in run-time

Advanced Analog Features

• ADC Module:

- 10-bit 1.1 Msps rate with one SH

- Up to 10 analog inputs on 28-pin devices and 13 analog inputs on 44-pin devices

• Flexible and independent ADC trigger sources

• Charge Time Measurement Unit (CTMU):

- Supports mTouch™ capacitive touch sensing

- Provides high-resolution time measurement (1 ns)

- On-chip temperature measurement capability

• Comparators:

- Up to three Analog Comparator modules

- Programmable references with 32 voltage points

Timers/Output Compare/Input Capture

• Five General Purpose Timers:

- Five 16-bit and up to two 32-bit Timers/Counters

• Five Output Compare (OC) modules

• Five Input Capture (IC) modules

• Peripheral Pin Select (PPS) to allow function remap

• Real-Time Clock and Calendar (RTCC) module

Communication Interfaces

• USB 2.0-compliant Full-speed OTG controller

• Two UART modules (10 Mbps)

- Supports LIN 2.0 protocols and IrDA® support

• Two 4-wire SPI modules (20 Mbps)

• Two I2C modules (up to 1 Mbaud) with SMBus support

• Peripheral Pin Select (PPS) to allow function remap

• Parallel Master Port (PMP)

Direct Memory Access (DMA)

• Four channels of hardware DMA with automatic data size detection

• Two additional channels dedicated for USB

• Programmable Cyclic Redundancy Check (CRC)

Input/Output

• 15 mA source/sink on all I/O pins

• 5V-tolerant pins

• Selectable open drain, pull-ups, and pull-downs

• External interrupts on all I/O pins

Qualification and Class B Support

• AEC-Q100 REVG (Grade 2 -40ºC to +105ºC) planned

• Class B Safety Library, IEC 60730

Debugger Development Support

• In-circuit and in-application programming

• 4-wire MIPS® Enhanced JTAG interface

• Unlimited program and six complex data breakpoints

• IEEE 1149.2-compatible (JTAG) boundary scan

PIC32MX應用:

High Impact Graphics/User Interfaces

Ethernet/USB/CAN/Connectivity

Multitasking Embedded Control

High Performance Audio

圖1.PIC32MX方框圖

多媒體擴展板(MEB)

This compact, highly versatile board can be connected to any PIC32 starter kit for the purpose of developing multimedia applications, such as audio, graphics and touch screen.