[C51代碼]MAX7219驅動

#ifndef _max7219_h_
#define _max7219_h_

#include
#include "link.h"
/***************控制引腳定義****************/
sbit _7219_DIN = P2^0;
sbit _7219_CS = P2^1;
sbit _7219_CLK = P2^2;

/***************控制字定義****************/
#define _7219_NO_OP0x00 //Digit0~Digit7位于RAM的地址
#define _7219_DIG00x01
#define _7219_DIG10x02
#define _7219_DIG20x03
#define _7219_DIG30x04
#define _7219_DIG40x05
#define _7219_DIG50x06
#define _7219_DIG60x07
#define _7219_DIG70x08

#define _7219_DECODE0x09 //譯碼方式地址
#define _7219_INTENSITY0x0A //亮度寄存器地址
#define _7219_SCANLIMIT0x0B //掃描界限寄存器地址，用于設置外接數碼管個數
#define _7219_SHUTDOWN0x0C //停機寄存器地址，使其處于低功耗
#define _7219_DISPTEST0x0F //顯示測試寄存器地址，用于測試數碼管和MAX2719是否工作

//Decode Mode
#define _7219_DECODE_ALL0xff
#define _7219_DECODE_NONE0x00

// Intensity
#define _7219_INTENSITY_MIN0x01
#define _7219_INTENSITY_MAX0x0f

// Scanlimit
#define _7219_SCANLIMIT_70x07
#define _7219_SCANLIMIT_60x06
#define _7219_SCANLIMIT_50x05
#define _7219_SCANLIMIT_40x04
#define _7219_SCANLIMIT_30x03
#define _7219_SCANLIMIT_20x02
#define _7219_SCANLIMIT_10x01
#define _7219_SCANLIMIT_00x00

//Shutdown mode
#define _7219_SHUTDOWN_ON 0x01
#define _7219_SHUTDOWN_OFF 0x00

//Display test
#define _7219_DISPTEST_ON0x01
#define _7219_DISPTEST_OFF 0x00

//7219 CODE B
//BCD譯碼對應的字符段位
#define _7219_00x00
#define _7219_10x01
#define _7219_20x02
#define _7219_30x03
#define _7219_40x04
#define _7219_50x05
#define _7219_60x06
#define _7219_70x07
#define _7219_80x08
#define _7219_90x09
#define _7219_E0x0B
#define _7219_H0x0C
#define _7219_L0x0D
#define _7219_P0x0E
#define _7219_BLANK0x0F

//7219 NO Code
#define _7219_SEG_DP7
#define _7219_SEG_A6
#define _7219_SEG_B5
#define _7219_SEG_C4
#define _7219_SEG_D3
#define _7219_SEG_E2
#define _7219_SEG_F1
#define _7219_SEG_G0

/***************函數聲明****************/
extern void Write_Max7219(uchar Addr, uchar Content);
extern void Init_Max7219();

#endif

/**************************max7219.c*******************************/

#include "max7219.h"
#include "link.h"
#include

/****************************************************************
*函數功能：寫入一個字節到max7219
*入口參數：數據Content
*出口參數：無
*****************************************************************/
void Write_Max7219_byte(unsigned char temp)
{
unsigned char i;
for (i=0;i<8;i++)
{
_7219_CLK=0;
_7219_DIN=(bit)(temp&0x80);
temp<<=1;
_7219_CLK=1;
}
}
/****************************************************************
*函數功能：在max7219指定的地址寫入一個字節的內容
*入口參數：要寫入數據的地址：Address
寫入數據的具體值：Content
*出口參數：無
****************************************************************/
void Write_Max7219(unsigned char address,unsigned char dat)
{
_7219_CS=0;
Write_Max7219_byte(address);
Write_Max7219_byte(dat);
_7219_CS=1;
}

/****************************************************************
*函數功能：配置max7219的基本參數
*入口參數：無
*出口參數：無
****************************************************************/
void Init_Max7219()
{
Write_Max7219(_7219_SHUTDOWN , _7219_SHUTDOWN_OFF);
Write_Max7219(_7219_INTENSITY, 0x05);
Write_Max7219(_7219_DECODE , _7219_DECODE_ALL);
Write_Max7219(_7219_DISPTEST , _7219_DISPTEST_OFF);
Write_Max7219(_7219_SHUTDOWN , _7219_SHUTDOWN_ON);
Write_Max7219(_7219_SCANLIMIT , _7219_SCANLIMIT_7);
}