STM8L探索套件學習筆記-綜合應用（十八）

今天使用到的外設比較多，有DMA,TIM1,ADC。使用ADC1的通道24即PF1采集電位器的電壓，由DMA1的通道0傳輸?shù)紹uffer。同時由DMA1的通道2將Buffer傳輸?shù)絋IM1外設上，也就是TIM1_CCR1H寄存器，能夠改變PWM波的占空比。我們將PWM輸出端連接到板上LED3上，這樣就實現了用電位器調節LED3的亮度的作用。我們轉了這么大彎，但能夠?qū)W到很多，下面是代碼：
void main(void)
{
//1使能時鐘
/* Enable ADC1 clock */
CLK_PeripheralClockConfig(CLK_Peripheral_ADC1, ENABLE);

/* Enable TIM1 clock */
CLK_PeripheralClockConfig(CLK_Peripheral_TIM1, ENABLE);

/* Enable DMA1 clock */
CLK_PeripheralClockConfig(CLK_Peripheral_DMA1, ENABLE);
//2設置ADC
/* Initialise and configure ADC1 */
ADC_Init(ADC1, ADC_ConversionMode_Continuous, ADC_Resolution_12Bit, ADC_Prescaler_2);
ADC_SamplingTimeConfig(ADC1, ADC_Group_SlowChannels, ADC_SamplingTime_384Cycles);

/* Enable ADC1 */
ADC_Cmd(ADC1, ENABLE);

/* Enable ADC1 Channels 24 */
ADC_ChannelCmd(ADC1, ADC_Channel_24, ENABLE); /* connected to potentiometer */
//3設置DMA通道0連接ADC1，通道2連接TIM1
/* Connect ADC1 to DMA1 channel 0 */
SYSCFG_REMAPDMAChannelConfig(REMAP_DMA1Channel_ADC1ToChannel0);
DMA_Init(DMA1_Channel0,
BUFFER_ADDRESS,
ADC1_DR_ADDRESS,
BUFFER_SIZE,
DMA_DIR_PeripheralToMemory,
DMA_Mode_Circular,
DMA_MemoryIncMode_Inc,
DMA_Priority_High,
DMA_MemoryDataSize_HalfWord);

/* Connect DMA1 channel 2 to TIM1 */
DMA_Init(DMA1_Channel2,
BUFFER_ADDRESS,
TIM1_CCR1_ADDRESS,
BUFFER_SIZE,
DMA_DIR_MemoryToPeripheral,
DMA_Mode_Circular,
DMA_MemoryIncMode_Inc,
DMA_Priority_High,
DMA_MemoryDataSize_HalfWord);

/* DMA1 Channel0 enable */
DMA_Cmd(DMA1_Channel0, ENABLE);

/* DMA1 Channel2 enable */
DMA_Cmd(DMA1_Channel2, ENABLE);

/* DMA1 enable */
DMA_GlobalCmd(ENABLE);
//4設置TIM1 CH1輸出PWM波
/* configure TIM1 channel 1 as PWM Output */
TIM1_OC1Init(TIM1_OCMode_PWM1,
TIM1_OutputState_Enable,
TIM1_OutputNState_Disable,
0x7FF/* TIM1_Pulse */,
TIM1_OCPolarity_Low,
TIM1_OCNPolarity_Low,
TIM1_OCIdleState_Reset,
TIM1_OCNIdleState_Reset);

/* Set TIM1 Autoreload value*/
TIM1_SetAutoreload(0xFFF);
//2M/4095=488.4HZ
/* Enable TIM1 */
TIM1_Cmd(ENABLE);

//5 PD2 TIM1 CH1設置
/* GPIO configuration: TIM1 channel 1 (PD2)*/
GPIO_Init(GPIOD, GPIO_Pin_2 , GPIO_Mode_Out_PP_Low_Fast);

//6使能
/* Enable TIM1 Outputs*/
TIM1_CtrlPWMOutputs(ENABLE);

/* Enable ADC1 DMA requests*/
ADC_DMACmd(ADC1, ENABLE);

/* Enable TIM1 DMA requests*/
TIM1_DMACmd(TIM1_DMASource_Update, ENABLE);

/* Start ADC1 Conversion using Software trigger*/
ADC_SoftwareStartConv(ADC1);

while (1)
{}
}