74HC595控制8位數碼管 51單片機

此程序已成功移植到STM32平臺，敬請關注！

// 注意 此代碼沒有什么技術含量，也沒有按規范些，旨在說明595怎么控制，大家不要模仿。

// 此代碼刷新速度有點慢，注意想辦法優化，time變量用定時器中斷處理，主函數不斷地刷新顯示函數，這樣就不會有閃屏，當然在STM32平臺毫無壓力

#include

sbit SCK = P3^2; // 數據輸入時鐘線，脈沖
sbit SI = P3^3; // 數據線
sbit RCK = P3^4; // 鎖存

unsigned char code SMG[10] = {0xC0, 0xF9, 0xA4, 0xB0, 0x99, 0x92, 0x82, 0xF8, 0x80, 0x90};
unsigned char Wei[8] = {0x01, 0x02, 0x04, 0x08, 0x10, 0x20, 0x40, 0x80};//位選
unsigned char Val[8] = {0};

void Output(void)
{
RCK = 0;
RCK = 1;
}

void Write_Byte(unsigned char dat)
{
unsigned char i = 0;
//每次發送一位數據，8次發送完畢，先發送高位（切記）
for(i=0; i<8; i++)
{
SCK = 0;
SI = dat & 0x80;
SCK = 1;

dat <<= 1;
}
}

void Display(unsigned char * p)
{
unsigned char * pt = Wei;
//注意，先發送位選，因為控制位選的595芯片在控制段選的595芯片下一級
Write_Byte(*(pt+0));//位選，
Write_Byte(SMG[*(p+0)]);//段選
Output();//發送到595 輸出

Write_Byte(*(pt+1));
Write_Byte(SMG[*(p+1)]);
Output();

Write_Byte(*(pt+2));
Write_Byte(SMG[*(p+2)]);
Output();

Write_Byte(*(pt+3));
Write_Byte(SMG[*(p+3)]);
Output();

Write_Byte(*(pt+4));
Write_Byte(SMG[*(p+4)]);
Output();

Write_Byte(*(pt+5));
Write_Byte(SMG[*(p+5)]);
Output();

Write_Byte(*(pt+6));
Write_Byte(SMG[*(p+6)]);
Output();

Write_Byte(*(pt+7));
Write_Byte(SMG[*(p+7)]);
Output();

}

int main(void)
{
unsigned long int time = 0;
unsigned int t = 0;

while(1)
{
t++;

if(100==t)
{
t= 0;
time++;

Val[0] = time / 10000000 % 10;
Val[1] = time / 1000000 % 10;
Val[2] = time / 100000 % 10;
Val[3] = time / 10000 % 10;
Val[4] = time / 1000 % 10;
Val[5] = time / 100 % 10;
Val[6] = time / 10 % 10;
Val[7] = time % 10;
}

Display(Val);
}

return 0;
}