十一 ARM9(2440)的網卡接口擴展

dm_reg_write(DM9000_NSR, 0x2c);//清除TX狀態

dm_reg_write(DM9000_IMR, 0x81);//打開DM9000接收數據中斷

}

int dm_rec_packet(unsigned char *datas)

{

unsigned char int_status;

unsigned char rx_ready;

unsigned short rx_status;

unsigned short rx_length;

unsigned short temp;

int i;

int_status = dm_reg_read(DM9000_ISR);//讀取ISR

if(int_status & 0x1)//判斷是否有數據要接受

{
dm_reg_write(DM9000_ISR,0x01);//清除中斷*******************F
rx_ready = dm_reg_read(DM9000_MRCMDX);//先讀取一個無效的數據
Uart_Printf("ready1=%dn",rx_ready);

rx_ready = (unsigned char)DM_DATA_PORT;//真正讀取到的數據包首字節
Uart_Printf("ready2=%dn",rx_ready);

if(rx_ready == 1)//判讀首字節是否為1或0

{

DM_ADDR_PORT = DM9000_MRCMD;//連續讀取數據包內容

rx_status = DM_DATA_PORT;//狀態字節

rx_length = DM_DATA_PORT;//數據長度

Uart_Printf("nlength=%dn",rx_length);

for(i=0; i//16位數據轉換為8位數據存儲

{

delay(20);

temp = DM_DATA_PORT;

datas[i] = temp & 0x0ff;

datas[i + 1] = (temp >> 8) & 0x0ff;

}
if((datas[12]==8)&&(datas[13]==6))
{
if((datas[20]==0)&&(datas[21]==1))
Uart_Printf("ARP請求n");
if((datas[20]==0)&&(datas[21]==2))
Uart_Printf("ARP應答n");
for(i=1; i<=rx_length; i++)
{
Uart_Printf("%d",datas[i-1]);
if(i%6==0)
Uart_Printf("n");
}
}

}

}

else if(rx_ready !=0)//停止設備

{

//dm_reg_write(DM9000_IMR,0x80);//停止中斷

//dm_reg_write(DM9000_ISR,0x0F);//清中斷狀態

//dm_reg_write(DM9000_RCR,0x0);//停止接收

//還需要復位系統，這里暫時沒有處理

}

dm_reg_write(DM9000_ISR, 0x1);//清中斷

return rx_length;

}

void __irq uartISR(void)

{

char ch;

rSUBSRCPND |= 0x1;

rSRCPND |= 0x1<<28;

rINTPND |= 0x1<<28;

ch=rURXH0;

if(ch == s)

tran=1;//表示發送一個ARP數據請求包

while(!(rUTRSTAT0 & 0x2));
rUTXH0=ch;
//for(i=0;i<100;i++);

}
void __irq DM9000ISR(void)

{

DisableIrq(BIT_EINT4_7);
Uart_Printf("nEINT7 Occuredn");

if(rEINTPEND&(1<<7))

{

rEINTPEND = rEINTPEND | (0x1<<7);

packet_len = dm_rec_packet(buffer);//接收網卡數據

}

rSRCPND = rSRCPND | (0x1<<4);

rINTPND = rINTPND | (0x1<<4);

EnableIrq(BIT_EINT4_7);

}

void init()
{
//uart0 port

rGPHCON = 0x00faaa;

rGPHUP= 0x7ff;

rULCON0 = 0x3;

rUCON0 = 0x5;

rUFCON0 = 0;

rUMCON0 = 0;

rUBRDIV0 = 26;

rSRCPND = (0x1<<27)|(0x1<<28);

rSUBSRCPND = 0x1;

rINTPND = (0x1<<27)|(0x1<<28);

rINTSUBMSK = ~(0x1);

rINTMSK = ~((0x1<<27)|(0x1<<28));

pISR_UART0 = (U32)uartISR;

//EINT7

rGPFCON = 2<<14;

rEXTINT0 = (rEXTINT0 & (~(0x07<<28))) | (0x01<<28);

rEINTMASK &= ~(1<<7);

rSRCPND = rSRCPND | (0x1<<4);

rINTPND = rINTPND | (0x1<<4);
rGPFCON = (rGPFCON & (~(0x03<<14))) | (0x02<<14);//GPF7設置為EINT7
rEXTINT0 = (rEXTINT0 & (~(0x07<<28))) | (0x01<<28);
rEINTMASK = rEINTMASK & (~(0x01<<7));
ClearPending(BIT_EINT4_7);

pISR_EINT4_7 = (U32)DM9000ISR;
rINTMSK &= ~(1<<4);

}

void Main(void)

{
tran=0;
MMU_Init();
init();
dm_init();

while(1)
{
if(tran==1)
{
dm_tran_packet(arpsendbuf1, 42 );//因為PC機不斷向外發送數據，其中剛開始就有ARP數據包，
tran=0;//所以為了方便查看，PC機通過串口發送s時，DM9000
}
//向PC機發送一個ARP數據請求，再收到的ARP數據就是PC機的應答信號

}

}