新聞中心

EEPW首頁 > 模擬技術 > 設計應用 > MAX1233/MAX1234觸摸屏控制器入門

MAX1233/MAX1234觸摸屏控制器入門

作者: 時間:2012-03-17 來源:網絡 收藏
TD>
I C 0 3
Configure KEYIRQ-bar pulse accumulator: falling-edge trigger
I 0 0
Reset the pulse accumulator
I R 0
Read the number of times KEYIRQ-bar has pulsed lowcount = 0
T W GC 0000
Keypad:
(C4,C3,C2,C1) x (R4,R3,R2,R1);
GPIO outputs: none;
GPIO inputs: none
0x004f 0x0000
T W KC bf00
Wait for keypress;
maximum debounce and hold times
0x0041 0xbf00
Press and release R1C1 (key "1")KEYIRQ pulse
I R 0
Read the number of times KEYIRQ-bar has pulsed lowcount has increased
T R KB
Read raw keypad result
0x8004 0x0000
0x0001 = R1C1 keyPress and release R2C2 (key "5")KEYIRQ pulse
I R 0
Read the number of times KEYIRQ-bar has pulsed lowcount has increased
T R KB
Read raw keypad result
0x8004 0x0000
0x0020 = R2C2 keyPress and release R3C2 (key "8")KEYIRQ pulse
I R 0
Read the number of times KEYIRQ-bar has pulsed lowcount has increased
T R KB
Read raw keypad result
0x8004 0x0000
0x0040 = R3C2 key

4.4) 從鍵盤中屏蔽單個按鍵

使用鍵盤屏蔽寄存器和鍵盤2結果寄存器來屏蔽每個按鍵。屏蔽掉的按鍵被掃描至KPD寄存器,但是不在鍵盤2結果寄存器中報告。

表17. 按鍵命令序列:屏蔽單個按鍵
DEMO1234 Command
Action
SPI data in
Verification
T W GC 0000
Keypad:
(C4,C3,C2,C1) x (R4,R3,R2,R1);
GPIO outputs: none;
GPIO inputs: none
0x004f 0x0000
T W KC bf00
Wait for keypress;
maximum debounce and hold times
0x0041 0xbf00
T W KM 0020
Mask only R2C2 key
0x0050 0x0020
Press and release R1C1 (key "1")
T R KB
Read raw keypad result
0x8004 0x0000
0x0001 = R1C1 key
T R K2
Read masked keypad result
0x8011 0x0000
0x0001 = R1C1 key
Press and release R2C2 (key "5")
T R KB
Read raw keypad result
0x8004 0x0000
0x0020 = R2C2 key
T R K2
Read masked keypad result
0x8011 0x0000
0x0000 = no key
Press and release R3C2 (key "8")
T R KB
Read raw keypad result
0x8004 0x0000
0x0040 = R3C2 key
T R K2
Read masked keypad result
0x8011 0x0000
0x0040 = R3C2 key

4.5) 從鍵盤中屏蔽一列

使用鍵盤列寄存器來屏蔽所有列。不掃描屏蔽列,因此,KPD寄存器不會探測這些列中的按鍵。

表18. 按鍵命令序列:屏蔽鍵盤的一列
DEMO1234 Command
Action
SPI data in
Verification
T W GC 0000
Keypad:
(C4,C3,C2,C1) x (R4,R3,R2,R1);
GPIO outputs: none;
GPIO inputs: none
0x004f 0x0000
T W KC bf00
Wait for keypress;
maximum debounce and hold times
0x0041 0xbf00
T W KK 2000
Mask entire C2 column
0x0051 0x2000
Press and release R1C1 (key "1")
T R KB
Read raw keypad result
0x8004 0x0000
0x0001 = R1C1 key
Press and release R2C2 (key "5")
T R KB
Read raw keypad result
0x8004 0x0000
(previous value)
Press and release R3C2 (key "8")
T R KB
Read raw keypad result
0x8004 0x0000
(previous value)
Press and release R2C3 (key "6")
T R KB
Read raw keypad result
0x8004 0x0000
0x0200 = R2C3 key

5) 電源管理

表19. 關斷命令
DEMO1234 Command
Action
SPI data in
Verification
T W AC C000
Power off ADC
0x0040 0xc000
T W AC 0300
Power off internal reference
0x0040 0x0300
REF = not driven
T W DC 8000
Disable DAC
0x0042 0x8000
DACOUT = 0.0V
T W KC C000
Power off keypad
0x0041 0xc000

6) 菜單系統

全部源代碼實現下面的控制臺菜單系統,它連接至MINIQUSB+模塊。

CmodComm測試程序主菜單—在連接前
A) adjust timing parameters
L) CmodLog... functions
C) connect
D) Debug Messages
X) exit

對C (連接)命令的響應
C
Hardware supports optimized native SMBus commands.

Board connected.

Got board banner: Maxim MINIQUSB V01.05.41 >
Firmware version is OK.
(configured for SPI auto-CS 4-byte mode) (SCLK=2MHz) ...

主菜單—連接后有效
T) Test the device
8) CmodP8Bus... functions
A) adjust timing parameters
L) CmodLog... functions
P) CmodPin... functions
S) CmodSpi... functions
M) CmodSMBus... functions
$) CmodCommStringWrite list of hex codes

R) CmodBoardReset
D) Disconnect

測試菜單命令—連接后有效
R) Read register
W) Write register
M0) measure no measurement; configure reference
M1) measure X,Y
M2) measure X,Y,Z1,Z2
M3) measure X
M4) measure Y
M5) measure Z1,Z2
M6) measure BAT1/4
M7) measure BAT2/4
M8) measure AUX1
M9) measure AUX2
MA) measure TEMP1
MB) measure BAT1/4,BAT2/4,AUX1,AUX2,TEMP1,TEMP2
MC) measure TEMP1,TEMP2
MD) no measurement; drive Y+,Y-
ME) no measurement; drive X+,X-
MF) no measurement; drive Y+,X-
.) Exit this menu

6.1) 寄存器讀/寫命令

表20. 讀取寄存器助記符
  • DEMO1234 Command
    Mnemonic
    SPI data in
    T R A1
    Test Read AUX1 register
    0x8007 0x0000
    T R A2
    Test Read AUX2 register
    0x8008 0x0000
    T R AC
    Test Read ADC_control register
    0x8040 0x0000
    T R AX
    Test Read X register
    0x8000 0x0000
    T R AY
    Test Read Y register
    0x8001 0x0000
    T R AZ1
    Test Read Z1 register
    0x8002 0x0000
    T R AZ2
    Test Read Z2 register
    0x8003 0x0000
    T R B1
    Test Read BAT1 register
    0x8005 0x0000


    評論


    相關推薦

    技術專區