CAT6500自動電源選擇開關詳細介紹
英飛凌汽車電子生態圈
CAT6500 is an automatic power switch designed to select between two power sources and direct that power to a load for battery charging or system power.
本文引用地址：http://butianyuan.cn/article/258549.htmCAT6500’s power inputs withstand voltages of up to 18 V and protect the downstream load from voltages exceeding 7V. In the event of a polarity reversal at either input CAT6500’s internal power switches will shut off to prevent discharge of the system’s internal power source.
功能框圖：
CAT6500功能框圖
管腳定義：
CAT6500管腳定義
引腳功能描述：
Pin No. | Pin Name | Description | |
1, 2, 3, 4 | PWR_OUT | Power Output. Must be tied to PWR_OUT on opposite side of chip. Use all 3 pins each side. | |
5 | NIC | No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. | |
6, 7, 8, 9, 10 | PS2 | Power Source #2. External power input | |
11, 12 | NIC | No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. | |
13 | VCC | Power input from battery. | |
14 | GND | Ground. Reference point for all voltages. | |
15 | C1 | Filter capacitor for CAT6500’s internal power bus | |
16 | NIC | No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. | |
17 | NIC | No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. | |
18 | PRIORITY | Priority selects preferred power source when both PS1 and PS2 are powered. | |
19 | RM_EN2 | Reverse Mode Enable 2. Overrides PRIORITY and turns SW2 ON. | |
20 | GND | Ground. Reference point for all voltages. | |
21 | RM_EN1 | Reverse Mode Enable 1. Overrides PRIORITY and turns SW1 ON. | |
22 | PS1 | Power Source #1. External power input. | |
23 | SW2_STAT | Power Source 2 Status. An open drain LOW true logic level output indicating that the switch SW2 is | |
24 | SW1_STAT | Power Source 1 Status. An open drain LOW true logic level output indicating that the switch SW1 is | |
25, 26, 27, 28 | PS1 | Power Source #1. External power input. | |
29 | NIC | No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. | |
30, 31, 32 | PWR_OUT | Power Output. Must be tied to PWR_OUT on opposite side of chip. Use all 3 pins each side. | |
33 | PWR_OUT | Electrically active thermal pad. Does not need to be connected to other PWR_OUTs. Can be left float-ing but must not be connected to other signal paths or Ground. | |
34 | PS2 | Electrically active thermal pad. Does not need to be connected to other PS2 pins. Can be left floating but must not be connected to other signal paths or Ground. | |
35 | – | Mechanical support for control IC. This chip does not generate any significant heat and does not need a separate heat sinking connection. Electrically this may be left floating or can be grounded. It should NOT be connected to other signals or voltages. | |
36 | PS1 | Electrically active thermal pad. Does not need to be connected to other PS1 pins. Can be left floating but must not be connected to other signal paths or Ground. |
CAT6500技術方案、應用案例、電路圖集錦
涵蓋了CAT6500的技術方案和CAT6500的應用筆記以及CAT6500的電路圖，為工程師學習CAT6500提供了一站式學習環境。
評論