十 ARM9(2440)的IIC-理論知識及程序?qū)嵗?/h1>

作者： 時間：2016-11-27 來源：網絡

• 加入技術交流群
  • 
    掃碼加入
    和技術大咖面對面交流
    海量資料庫查詢

收藏

//*************************[ Wr24C080 ]****************************
void Wr24C080(U32 slvAddr,U32 addr,U8 data)//首地址內部地址數據
{
_iicMode= WRDATA;//模式標志記為WRDAT
_iicPt= 0;//指針記為0
_iicData[0]= (U8)addr;//內部地址
_iicData[1]= data;// 要寫的數據
_iicDataCount = 2;

rIICDS= slvAddr;//0xa0設備地址
rIICSTAT = 0xf0;//MasTx,Start 啟動發送
//Clearing the pending bit isnt needed because the pending bit has been cleared.

while(_iicDataCount!=-1);//未發送完在此等待

本文引用地址：http://butianyuan.cn/article/201611/322175.htm

_iicMode = POLLACK;//發送完后下面等待應答信號ACK

while(1)
{
rIICDS= slvAddr;
_iicStatus = 0x100;
rIICSTAT= 0xf0;//MasTx,Start啟動
rIICCON= 0xaf;//Resumes IIC operation. 恢復IIC總線

while(_iicStatus==0x100);//未接收到ACk在此等待

if(!(_iicStatus&0x1))
break;//When ACK is receivedACK收到后跳出循環
}
rIICSTAT = 0xd0;//Stop MasTx condition 停止信號
rIICCON= 0xaf;//Resumes IIC operation.
Delay(1);//Wait until stop condtion is in effect.恢復
//Write is completed.
}

//**********************[ Rd24C080 ] ***********************************
void Rd24C080(U32 slvAddr,U32 addr,U8 *data)//首地址 內部地址 讀取的數據存入的地址
{
_iicMode= SETRDADDR;//模式設為SETRDADDR
_iicPt= 0;
_iicData[0]= (U8)addr;//_iicData[0]存內部地址
_iicDataCount = 1;//計數值

rIICDS= slvAddr;//首地址0xa0
rIICSTAT = 0xf0;//MasTx,Start啟動
//Clearing the pending bit isnt needed because the pending bit has been cleared.
while(_iicDataCount!=-1);//未讀取完成

_iicMode= RDDATA;//完成后進入讀取數據模式
_iicPt= 0;
_iicDataCount = 1;

rIICDS= slvAddr;
rIICSTAT= 0xb0;//MasRx,Start設置為主接收模式
rIICCON= 0xaf;//Resumes IIC operation.恢復IIC總線操作
while(_iicDataCount!=-1);//讀取未完成

*data = _iicData[1];//1
}

//-------------------------------------------------------------------------
void __irq IicInt(void)
{
U32 iicSt,i;

rSRCPND = BIT_IIC;//Clear pending bit
rINTPND = BIT_IIC;
iicSt= rIICSTAT;//控制狀態寄存器

if(iicSt & 0x8){}//When bus arbitration is failed.總線仲裁失敗執行空操作
if(iicSt & 0x4){}//When a slave address is matched with IICADD從地址匹配執行空操作
if(iicSt & 0x2){}//When a slave address is 0000000b
if(iicSt & 0x1){}//When ACK isnt received未收到應答信號執行空操作

switch(_iicMode)
{
case POLLACK:
_iicStatus = iicSt;//控制狀態寄存器的值賦給_iicStatus
break;

case RDDATA:
if((_iicDataCount--)==0)
{
_iicData[_iicPt++] = rIICDS;

rIICSTAT = 0x90;//Stop MasRx condition
rIICCON= 0xaf;//Resumes IIC operation.
Delay(1);//Wait until stop condtion is in effect.
//Too long time...
//The pending bit will not be set after issuing stop condition.
break;
}
_iicData[_iicPt++] = rIICDS;//The last data has to be read with no ack.

if((_iicDataCount)==0)
rIICCON = 0x2f;//Resumes IIC operation with NOACK.第一次不產生應答信號進行第二次讀取并將第二次讀取的
///////////////數據存入數組中（第一次和第二次讀取的數據實際一樣）
else
rIICCON = 0xaf;//Resumes IIC operation with ACK
break;

case WRDATA:
if((_iicDataCount--)==0)//首地址 ，內部地址和數據都發送完畢后
{
rIICSTAT = 0xd0;//Stop MasTx condition 產生停止信號
rIICCON= 0xaf;//Resumes IIC operation.恢復IIC總線
Delay(1);//Wait until stop condtion is in effect.
//The pending bit will not be set after issuing stop condition.
break;
}
rIICDS = _iicData[_iicPt++];//_iicData[0] has dummy.第一次中斷后將內部地址addr的值存入IICDS第二次存入要寫入的數據
for(i=0;i<10;i++);//for setup time until rising edge of IICSCL//延時

rIICCON = 0xaf;//resumes IIC operation.恢復IIC總線
break;

case SETRDADDR:
//Uart_Printf("[ S%d ]",_iicDataCount);
if((_iicDataCount--)==0)
break;//第二次中斷跳出//IIC operation is stopped because of IICCON[4]
rIICDS = _iicData[_iicPt++];//第一次中斷將內部地址addr存入移位寄存器
for(i=0;i<10;i++);//For setup time until rising edge of IICSCL
rIICCON = 0xaf;//Resumes IIC operation.
break;

default:
break;
}
}
void Delay(int x)
{
int k, j;
while(x)
{
for (k=0;k<=0xff;k++)
for(j=0;j<=0xff;j++);

x--;
}
}

上一頁 1 2 下一頁