PIC16F917 電壓表

/*************PIC16F917單片機程序******************************/
/*********************************************************************/
/*****File Function : AD采集，LCD顯示程序*****/
/*****Program Author : ZhengWen(ClimberWin)*****/
/*****MCU ： PIC16F917 內部晶振*****/
/*****Compile Date : 2010/08/18 *****/
/*****Edition Info : V1.0 *****/
/*************************************************************/
//測量AD，并且通過LCD來進行顯示
//引腳定義：PORTD=8LED，KEY=RB0(INT) RA5(AN4)作為AD輸入
/*修改日期: */

/************************************/
#include
#include "english_6x8_pixel.h"
#define uchar unsigned char
#define uint unsigned int
void Init(void); //初始化子程序
void LCD_init(void); //LCD初始化程序
void LCD_clear(void);
void LCD_write_char(unsigned char c);
void LCD_set_XY(unsigned char X, unsigned char Y);
void LCD_write_english_string(unsigned char X,unsigned char Y,const char *s);
void LCD_write_byte(unsigned char data, unsigned char command);
void delayms(unsigned int count);
void interrupt ADint(void);

#define KEY RB0
#define SPI_CLK RD0
#define SPI_MOSI RD1
#define LCD_DC RD2
#define LCD_CE RD3
#define LCD_RST RD4
/***********************************************/

const unsigned char mask_table[8]={0x80,0x40,0x20,0x10,0x08,0x04,0x02,0x01};
float ad_data;//AD數據存儲地址
uchar temp1,temp2;
uint temp3;
/*********************************************/
void delayms(unsigned int count)
{
uint i,j;
for(i=0;ifor(j=0;j<120;j++);
}
/*********************************************/
void Init(void)
{
PORTA = 0B00000000;
PORTB = 0B00000000;
PORTD = 0B00000000;

TRISA = 0B00100010;//設置RA5(AN4) RA1作為輸入
TRISB = 0B00100001;//設置RB0為輸入，作為按鍵口
TRISD = 0B00000000;//設置PORTD口為輸出，作為LCD/LED顯示口
RD5=1;//關閉LED
RD6=1;
RD7=1;

///////////AD配置///////////////////////////////////////
ANSEL= 0B00010000; //選擇AN4作為AD輸入 (PDF 148)
ADCON0=0B10010001;//AD結果格式Right justified，選擇參考電壓VDD-VSS，AN4輸入，關閉AD轉換
ADCON1=0B01010000; //AD轉換時鐘選擇

ADIE=1;//AD中斷使能
PEIE=1;
ADIF=0;//清除中斷標志位
GIE=1; //開總中斷
/////////////////////////////////////
LCD_init(); //初始化液晶
}

void interrupt ADint(void)
{

temp1=ADRESL;
temp2=ADRESH;
temp3=temp2*256+temp1; //Dx值
ad_data=(temp3*33000)/1024; //電壓值
ADIF=0;//清除中斷標志位

}

void LCD_init(void)
{
LCD_RST=0; //LCD復位
NOP();
LCD_RST=1;

LCD_CE=0 ;// 關閉LCD
NOP();
LCD_CE=1;// 使能LCD
NOP();

LCD_write_byte(0x21, 0);// 使用擴展命令設置LCD模式
LCD_write_byte(0xc8, 0);// 設置偏置電壓
LCD_write_byte(0x06, 0);// 溫度校正
LCD_write_byte(0x13, 0);// 1:48
LCD_write_byte(0x20, 0);// 使用基本命令
LCD_clear(); // 清屏
LCD_write_byte(0x0c, 0);// 設定顯示模式，正常顯示

LCD_CE=0 ; // 關閉LCD
}

/////////LCD清屏程序/////////////
void LCD_clear(void)
{
uint i;
LCD_write_byte(0x0c, 0);
LCD_write_byte(0x80, 0);
for (i=0; i<504; i++)
LCD_write_byte(0x00, 1);//清零
}

///////////設置LCD坐標///////////////////
void LCD_set_XY(unsigned char X, unsigned char Y)
{
LCD_write_byte(0x40 | Y, 0);
LCD_write_byte(0x80 | X, 0);
}

////////////////字符顯示程序/////////////////////
void LCD_write_char(unsigned char c)
{
uint line;
c=c-32;
for (line=0; line<6; line++)
LCD_write_byte( font6x8[c][line], 1);
}

/////////////////打印字符串/////////////////////////
void LCD_write_english_string(unsigned char X,unsigned char Y, const unsigned char *s)
{
uchar i = 0;
LCD_set_XY(X,Y);
while(*s) {LCD_write_char(*s++);}
}

////////////寫數據到LCD//////////////////////
void LCD_write_byte(unsigned char data, unsigned char command)
{
uchar i;
LCD_CE=0 ; // 使能LCD

if (command == 0)
{LCD_DC=0 ;} // 傳送命令
else
{LCD_DC=1 ;} // 傳送數據

for(i=0;i<8;i++)
{
if(data&mask_table[i])
{SPI_MOSI=1;}
else
{SPI_MOSI=0;}
SPI_CLK=0;
NOP();
SPI_CLK=1;
}

LCD_CE=1 ;// 關閉LCD
}

////////////主程序/////////////////////////
void main (void)
{

Init();//初始化程序
LCD_clear(); //LCD清屏
delayms(1000);
LCD_write_english_string(0,0," AD Test " );
LCD_write_english_string(0,1,"AD4 Vref=3.3V" );

ADCON0=ADCON0|0B00000010;//開始AD轉換
LCD_set_XY(0,3);
LCD_write_char(D);
LCD_write_char(x);
LCD_write_char( );
LCD_write_char(=);

LCD_set_XY(0,5);
LCD_write_char(V);
LCD_write_char(i);
LCD_write_char(n);
LCD_write_char(=);
LCD_set_XY(72,5);
LCD_write_char(V);
while(1)
{
LCD_set_XY(30,3);
LCD_write_char((temp3/1000)+16+32);
LCD_write_char( (temp3%1000)/100+16+32);
LCD_write_char( ((temp3%1000)%100)/10+16+32);
LCD_write_char( ((temp3%1000)%100)%10+16+32);

//ad_data=ad_data*10000;
temp3=(uint)ad_data;
LCD_set_XY(30,5);
LCD_write_char((temp3/10000)+16+32);
LCD_write_char(.);
LCD_write_char( (temp3%10000)/1000+16+32);
LCD_write_char( ((temp3%10000)%1000)/100+16+32);
LCD_write_char( (((temp3%10000)%1000)%100)/10+16+32);
LCD_write_char( (((temp3%10000)%1000)%100)%10+16+32);

delayms(100);
ADCON0=ADCON0|0B00000010;//開始AD轉換

}

}