ARM匯編外部中斷

調試比較久的原因：使用main: b main時調試發現，不能死循環，可能是main標簽是保留的

1）在主程序中的步驟一般是：

1.關中斷，并設置各主要模式的堆棧指針和容量

2寫1清SRCPND，INTPND寄存器

3.配置INTMSK使能相應中斷

4.開全局中斷

3）中斷服務程序中的流程是：

1.屏蔽中斷(硬件自動關irq中斷)

2.執行任務

3.寫1清相應SRPND，INTPND等寄存器（可以利用SRPND=SRPND，INTPND來清零，防止出錯）

4.把屏蔽的中斷使能回來

5.返回

參考u-boot的start.S自己寫了一個外部中斷程序，mini2440的按鍵K1，按一下LED滅，再按一下LED亮......。硬件原理圖：按鍵引腳對應GPIO是PG0，對應EINT8，而LED的引腳是PB8，被設計為低電平時燈亮。

.equ    NOINT,      0xc0  .equ    DISABLE_IRQ,0x80.equ    SYS_MOD,    0x1f.equ    IRQ_MOD,    0x12.equ	USR_MOD,    0x10.equ    WTCON,    0x53000000.equ    GPBCON,   0x56000010.equ    GPBDAT,   0x56000014.equ    GPBUP,    0x56000018.equ    GPGCON,   0x56000060.equ    EINTMASK, 0x560000a4  .equ    EXTINT1,  0x5600008c .equ    EINTPEND, 0x560000a8  .equ    INTMSK,   0x4A000008  .equ    SRCPND,   0X4A000000  .equ    INTPND,   0X4A000010  .equ    USE_Stack, 4096.equ    IRQ_Stack, 2048.text.code 32.global _start_start: b resetldr     pc, _undefined_instruction  ldr     pc, _software_interrupt  ldr 	pc, _prefetch_abort  ldr	pc, _data_abort  ldr 	pc, _not_used  ldr     pc, _irq ldr     pc, _fiq_undefined_instruction:     .word undefined_instruction  _software_interrupt:        .word software_interrupt  _prefetch_abort:            .word prefetch_abort  _data_abort:                .word data_abort  _not_used:                  .word not_used  _irq:                       .word irq  _fiq:                       .word fiq.balignl 16,0xdeadbeefreset:ldr r0,=WTCONmov r1,#0x0str r1,[r0] @關看門狗ldr r0,=GPBCONldr r1,=0x10000str r1,[r0] @PB8輸出ldr r0,=GPBDATmov r1,#0x000str r1,[r0] @低電平msr cpsr_c,#(IRQ_MOD|NOINT)ldr sp,=IRQ_Stackmsr cpsr_c,#(SYS_MOD|NOINT)ldr sp,=USE_Stackldr r0,=GPGCONmov r1,#0x02str r1,[r0] @使能外部中斷8ldr r0,=EXTINT1mov r1,#0x03str r1,[r0] @下降沿觸發ldr r0, =EINTPEND ldr r1,=0x00fffff0str r1,[r0]@ 清EINTPEND，寫1清零ldr r0,=EINTMASKldr r1,=0xfffffeffstr r1,[r0] @使能外部中斷8，0為使能ldr r0, =SRCPND ldr r1,=0xffffffffstr r1,[r0]@ 清SRCPND，寫1清零ldr r0, =INTPND ldr r1,=0xffffffff str r1,[r0]@ 清INTPND，寫1清零ldr r0,=INTMSKldr r1,=0xffffffdfstr r1,[r0] @使能外部中斷EINT8-23mrs r1, cpsr  bic r1, r1, #DISABLE_IRQmsr cpsr_c, r1 @開全局IRQ中斷l(xiāng)oop:	b loopirq_server:ldr r0, =EINTPENDldr r1,[r0]tst r1,#0x100 @判斷是否為EINT8beq not_handle ldr r0,=GPBDATldr r1,[r0]tst r1,#0x100 @測試PB8當前是高電平還是低電平ldreq r1,=0x100movne r1,#0x0str r1,[r0]not_handle:ldr r0, =EINTPEND ldr r1,[r0] @ldr r1,=0x100str r1,[r0] @清EINTPENDldr r0, =SRCPND ldr r1,[r0] @ldr r1,=0x20str r1,[r0] @清SRCPNDldr r0, =INTPND ldr r1,[r0] @ldr r1,=0x20str r1,[r0] @清INTPNDmov pc,lrundefined_instruction:  nop  software_interrupt:  nop  prefetch_abort:   nop  data_abort:  nop  not_used:  nop  irq:  sub     lr,lr,#4  stmfd   sp!,{r0-r12,lr}  bl irq_server  ldmfd  sp!,{r0-r12,pc}^fiq:  nop

OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") OUTPUT_ARCH(arm)ENTRY(_start)  SECTIONS{  . = 0x00000000;  .text : { *(.text)   }  .data ALIGN(4): {  *(.data)  }  .bss ALIGN(4): {  *(.bss)  }  }  

led_off.bin : led_off.Sarm-linux-gcc -nostdlib -nostartfiles -g -c -o led_off.o led_off.Sarm-linux-ld -Tint.lds led_off.o -o led_off_elfarm-linux-objcopy -O binary -S led_off_elf led_off.binclean:rm -f  led_off.bin led_off_elf *.o