C51單片機與PC串口通信的單片機部分程序

功能：電腦通過串口給單片機發一個字節，單片機收到后又給電腦發回去

#include
#define uchar unsigned char
#define uint unsigned int

uint temp;
bit flag;
void init_ser1();
main()
{
init_ser1();
while(1)
{
if(RI==1)
{
P1=SBUF;
RI=0;
}
if(flag==1)
{
ES=0;//暫時關閉接收
flag=0;
SBUF=temp;
while(!TI);//等待發送完畢
TI=0;
ES=1;
}
}
}

void sel() interrupt 4
{
RI=0;
P1=SBUF;
temp=SBUF;
flag=1;
}

void init_ser1()
{

REN=1;
SM0=0;
SM1=1;
TMOD=0x20;
TH1=0xFD;
TL1=0xFD;
EA=1;
TR1=1;
ES=1;
}

//======聲明======
#include
unsigned char Read_Keyboard();
void RS232_SendData(unsigned char Sdata);
//======延遲函數======
void delay(unsigned int t)
{
for(;t>0;t--); //延遲循環
}
//======UART初始化函數=====
void RS232_Init()
{
SCON=0x50; //0101 0000 UART工作模式1，REN=1(本位為串行接收啟用位1:開始接收 0:停止接收)
TMOD=0x20; //0010 0000 Timer1 工作模式2
PCON=0x80; //SMOD1=1
TH1=0xfa; //波特率9600 bps at 11.0592MHZ
TL1=0xfa; //波特率9600 bps at 11.0592MHZ
TR1=1;
}
//======主函數============
void main()
{
unsigned char Keyboard_Status=0xff; //定義按鍵
RS232_Init(); // 初始化UART
while(1)
{
Keyboard_Status=Read_Keyboard()|0xf0; //讀取按鍵值(屏蔽高4位)
//
switch(Keyboard_Status)
{
case ~0x01:RS232_SendData(A);break;
case ~0x02:RS232_SendData(B);break;
case ~0x04:RS232_SendData(C);break;
case ~0x08:RS232_SendData(D);break;
default:RS232_SendData(X);break;
}
}
}
//===========發送數據函數========
void RS232_SendData(unsigned char Sdata)
{
SBUF=Sdata; //發送數據
while(TI==0); //等待發送結束
TI=0; //清除發送結束標志
}
//========讀取按鍵函數==========
unsigned char Read_Keyboard()
{
unsigned char Keys_Value; //定義按鍵變量
unsigned char Keys_Temp;
do
{
P1=0xff; //P2口置高,準備讀取按鍵狀態
Keys_Temp=P1; //讀取按鍵狀態
delay(150); //消抖延時
P1=0xff; //P2口置高,準備讀取按鍵狀態
Keys_Value=P1; //讀取按鍵狀態
}
while(Keys_Value!=Keys_Temp); //如果讀狀態不一致,則重復讀取鍵值
return Keys_Value; //返回按鍵狀態值
}