avr eeprom保護方法.

在項目中復制出來的程序，使用時可能有些地方需要修改。
編譯環境：WinAVR-20060421+AVRStudio4.12.498ServicePack4
基本思路：每份寫到EEPRM的數據，都做三個備份，每個備份的數據都做CRC16校驗，只要系統運行中出錯，錯誤地修改了EEPROM數據，
那么根據校驗字節就知道哪個備份的數據被修改了，然后用正確的備份覆蓋出錯的備份，達到數據恢復的目的。
EEPROMSave.h文件：
#defineEepromPageSize 64 //頁容量定義
#defineEepromPage0Addr 0x0000 //各個頁的其始地址定義
#defineEepromPage1Addr (EepromPage0Addr+EepromPageSize)
#defineEepromPage2Addr (EepromPage1Addr+EepromPageSize)
#defineEepromPage3Addr (EepromPage2Addr+EepromPageSize)
#defineEepromPage4Addr (EepromPage3Addr+EepromPageSize)
#defineEepromPage5Addr (EepromPage4Addr+EepromPageSize)
#defineEepromPage6Addr (EepromPage5Addr+EepromPageSize)
#defineEepromPage7Addr (EepromPage6Addr+EepromPageSize)
#defineVALID 0x01
#defineINVALID 0x00
EEPROMSave.c文件：
unsignedcharEepromReadByte(unsignedchar*address)
{
unsignedchardata;
data=0;
eeprom_busy_wait();
data=eeprom_read_byte(address);
returndata;
}
uint16_tEepromReadWord(uint16_t*address)
{
uint16_tdata;
data=0;
eeprom_busy_wait();
data=eeprom_read_word(address);
returndata;
}
voidEepromWriteByte(unsignedchar*address,unsignedchardata)
{
eeprom_busy_wait();
eeprom_write_byte(address,data);
}
voidEepromWriteWord(unsignedint*address,unsignedintdata)
{
eeprom_busy_wait();
eeprom_write_word(address,data);
}
voidEepromWriteBlock(unsignedchar*buff,unsignedchar*address,unsignedcharn)
{
unsignedchari;
for(i=0;i<n;i++)
{
EepromWriteByte((unsignedchar*)(address+i),*buff);
buff++;
}
}
unsignedcharEepromCheck(unsignedchar*pdata,unsignedcharpacksize)
{
unsignedchari,j;
unsignedintcrc,ref_crc;
crc=0;
ref_crc=0;
for(i=0;i<(packsize-2);i++)
{
crc=crc^((uint16_t)EepromReadByte(pdata)<<8);
for(j=0;j<8;j++)
{
if(crc&0x8000)
{
crc=(crc<<1)^0x1021;
}
else
{
crc=crc<<1;
}
}
pdata++;
}
ref_crc=(uint16_t)EepromReadByte(pdata);
ref_crc=ref_crc<<8;
pdata++;
ref_crc|=(uint16_t)EepromReadByte(pdata);
if(crc==ref_crc)
{
returnVALID;
}
else
{
returnINVALID;
}
}
unsignedcharCheckWriteCRC(unsignedchar*pdata,unsignedcharpacksize)
{
unsignedchari,j;
unsignedintcrc;
crc=0;
for(i=0;i<(packsize-2);i++)
{
crc=crc^((uint16_t)EepromReadByte(pdata)<<8);
for(j=0;j<8;j++)
{
if(crc&0x8000)
{
crc=(crc<<1)^0x1021;
}
else
{
crc=crc<<1;
}
}
pdata++;
}
EepromWriteByte(pdata,(uint8_t)(crc>>8));
pdata++;
EepromWriteByte(pdata,(uint8_t)crc);
pdata++;
if(EepromCheck((pdata-packsize),packsize))
{
returnVALID;
}
else
{
returnINVALID;
}
}
uint8_tCheckAllPage(void)
{
if((EepromCheck((unsignedchar*)EepromPage1Add,EepromPageSize)==VALID)
&&(EepromCheck((unsignedchar*)EepromPage2Add,EepromPageSize)==VALID)
&&(EepromCheck((unsignedchar*)EepromPage3Add,EepromPageSize)==VALID))
{
returnVALID;
}
returnINVALID;
}
uint8_tDataRecover(void)
{
unsignedchari;
unsignedchartemp;
unsignedcharpage;
unsignedintinvalidpage[3];
unsignedintvalidpage;
invalidpage[0]=0;
invalidpage[1]=0;
invalidpage[2]=0;
validpage=0;
temp=0;
page=0;
if(EepromCheck((uint8_t*)EepromPage1Add,EepromPageSize)==VALID)
{
validpage=EepromPage1Add;
}
else
{
invalidpage[page]=EepromPage1Add;
page++;
}
if(EepromCheck((uint8_t*)EepromPage2Add,EepromPageSize)==VALID)
{
validpage=EepromPage2Add;
}
else
{
invalidpage[page]=EepromPage2Add;
page++;
}
if(EepromCheck((uint8_t*)EepromPage3Add,EepromPageSize)==VALID)
{
validpage=EepromPage3Add;
}
else
{
invalidpage[page]=EepromPage3Add;
page++;
}
if(page==3) //三個備份都被破壞了
{
returnINVALID; //數據完全無效了
}
while((page--)>0) //數據恢復
{
for(i=0;i<EepromPageSize;i++)
{
temp=EepromReadByte((uint8_t*)(validpage+i));
EepromWriteByte((uint8_t*)(invalidpage[page]+i),temp);
}
}
if(CheckAllPage()==VALID)
{
returnVALID;
}
returnINVALID;
}
使用方法(三個備份）：
1、定義一個數組：EEPROMData[EepromPageSize-2]，數組定義為EepromPageSize-2是為了給每個備份留2個字節的校驗
2、要保存數據時，先把數據放到數組中，然后調用EepromWriteBlock()函數，把這個數組的數據寫進EEPROM，三個備份要寫三次。
3、寫完了之后，調用CheckWriteCRC()函數，該函數會計算出當前備份的CRC16檢驗數據并寫到EEPROM備份的尾部，有多少個備份就要調用多少次。
4、至此，數據的備份工作已經完成。
5、校驗數據（一般在復位后運行），執行CheckAllPage()函數，若通過了，則EEPROM數據沒有問題，否則要運行DataRecover()函數，對損壞的備份進行修復